3.1  Transistors as Resistors

In Section 2.1, “CMOS Transistors,” we modeled transistors using ideal switches. If this model were accurate, logic cells would have no delay.


FIGURE 3.1  A model for CMOS logic delay. (a) A CMOS inverter with a load capacitance, C out . (b) Input, v(in1) , and output, v(out1) , waveforms showing the definition of the falling propagation delay, t PDf . In this case delay is measured from the input trip point of 0.5. The output trip points are 0.35 (falling) and 0.65 (rising). The model predicts t PDf ª R pd ( C p + C out ). (c) The model for the inverter includes: the input capacitance, C ; the pull-up resistance ( R pu ) and pull-down resistance ( R pd ); and the parasitic output capacitance, C p .

The ramp input, v(in1) , to the inverter in Figure  3.1 (a) rises quickly from zero to V DD . In response the output, v(out1) , falls from V DD to zero. In Figure  3.1 (b) we measure the propagation delay of the inverter, t PD , using an input trip point of 0.5 and output trip points of 0.35 (falling, t PDf ) and 0.65 (rising, t PDr ). Initially the n -channel transistor, m1 , is off . As the input rises, m1 turns on in the saturation region ( V DS > V GS V t n ) before entering the linear region ( V DS < V GS V t n ). We model transistor m1 with a resistor, R pd (Figure  3.1 c); this is the pull-down resistance . The equivalent resistance of m2 is the pull-up resistance , R pu .

Delay is created by the pull-up and pull-down resistances, R pd and R pu , together with the parasitic capacitance at the output of the cell, C p (the intrinsic output capacitance ) and the load capacitance (or extrinsic output capacitance ), C out (Figure  3.1 c). If we assume a constant value for R pd , the output reaches a lower trip point of 0.35 when (Figure  3.1 b),



t PDf



0.35 V DD =

V DD  exp






R pd ( C out + C p )



An output trip point of 0.35 is convenient because ln (1/0.35) = 1.04 ª 1 and thus

t PDf = R pd ( C out + C p ) ln (1/0.35) ª R pd ( C out + C p ) .


The expression for the rising delay (with a 0.65 output trip point) is identical in form. Delay thus increases linearly with the load capacitance. We often measure load capacitance in terms of a standard load —the input capacitance presented by a particular cell (often an inverter or two-input NAND cell).

We may adjust the delay for different trip points. For example, for output trip points of 0.1/0.9 we multiply Eq.  3.2 by –ln(0.1) = 2.3, because exp (–2.3) = 0.100.

Figure  3.2 shows the DC characteristics of a CMOS inverter. To form Figure  3.2 (b) we take the n -channel transistor surface (Figure 2.4b) and add that for a p -channel transistor (rotated to account for the connections). Seen from above, the intersection of the two surfaces is the static transfer curve of Figure  3.2 (a)—along this path the transistor currents are equal and there is no output current to change the output voltage. Seen from one side, the intersection is the curve of Figure  3.2 (c).



FIGURE 3.2  CMOS inverter characteristics. (a) This static inverter transfer curve is traced as the inverter switches slowly enough to be in equilibrium at all times ( I DSn = I DSp ). (b) This surface corresponds to the current flowing in the n -channel transistor (falling delay) and p -channel transistor (rising delay) for any trajectory. (c) The current that flows through both transistors as the inverter switches along the equilibrium path.


The input waveform, v(in1) , and the output load (which determines the transistor currents) dictate the path we take on the surface of Figure  3.2 (b) as the inverter switches. We can thus see that the currents through the transistors (and thus the pull-up and pull-down resistance values) will vary in a nonlinear way during switching. Deriving theoretical values for the pull-up and pull-down resistance values is difficult—instead we work the problem backward by picking the trip points, simulating the propagation delays, and then calculating resistance values that fit the model.







FIGURE 3.3  Delay. (a) LogicWorks schematic for inverters driving 1, 2, 4, and 8 standard loads (1 standard load = 0.034 pF in this case). (b) Transient response (falling delay only) from PSpice. The postprocessor Probe was used to mark each waveform as it crosses its trip point (0.5 for the input, 0.35 for the outputs). For example v(out1_4) (4 standard loads) crosses 1.0467 V ( ª 0.35 V DD ) at t = 169.93 ps. (c) Falling and rising delays as a function of load. The slopes in pspF –1 corresponds to the pull-up resistance (1281 W ) and pull-down resistance (817 W ). (d) Comparison of the delay model (valid for t > 20 ps) and simulation (4 standard loads). Both are equal at the 0.35 trip point.

Figure  3.3 shows a simulation experiment (using the G5 process SPICE parameters from Table 2.1). From the results in Figure  3.3 (c) we can see that R pd = 817 W and R pu = 1281 W for this inverter (with shape factors of 6/0.6 for the n -channel transistor and 12/0.6 for the p -channel) using 0.5 (input) and 0.35/0.65 (output) trip points. Changing the trip points would give different resistance values.

We can check that 817 W is a reasonable value for the pull-down resistance. In the saturation region I DS (sat) is (to first order) independent of V DS . For an n -channel transistor from our generic 0.5 m m process (G5 from Section 2.1) with shape factor W/L = 6/0.6, I DSn (sat) = 2.5 mA (at V GS = 3V and V DS = 3V). The pull-down resistance, R 1 , that would give the same drain–source current is

R 1 = 3.0 V / (2.5 ¥ 10 –3 A) = 1200 W .


This value is greater than, but not too different from, our measured pull-down resistance of 817 W . We might expect this result since Figure 3.2b shows that the pull-down resistance reaches its maximum value at V GS = 3V, V DS = 3V. We could adjust the ratio of the logic so that the rising and falling delays were equal; then R = R pd = R pu is the pull resistance .

Next, we check our model against the simulation results. The model predicts






v(out1) ª

V DD  exp


   for t ' > 0 .




R pd ( C out + C p )



( t' is measured from the point at which the input crosses the 0.5 trip point, t' = 0 at t = 20 ps). With C p = 4 standard loads = 4 ¥ 0.034 pF = 0.136 pF,

R pd ( C out + C p ) = (38 + 817 (0.136)) ps = 149.112 ps .


To make a comparison with the simulation we need to use ln (1/0.35) = 1.04 and not approximately 1 as we have assumed, so that (with all times in ps)









3.0 exp



















–( t – 20)





3.0 exp


   for t > 20 ps .








Equation 3.6 is plotted in Figure  3.3 (d). For v(out1) = 1.05 V (equal to the 0.35 output trip point), Eq.  3.6 predicts t = 20 + 149.112 ª 169 ps and agrees with Figure  3.3 (b)—it should because we derived the model from these results!

Now we find C p . From Figure  3.3 (c) and Eq.  3.2

t PDr = (52 + 1281 C out ) ps  thus   C pr = 52/1281 = 0.041 pF  (rising) ,




t PDf = (38 + 817 C out ) ps  thus   C pf = 38/817 = 0.047 pF  (falling) .


These intrinsic parasitic capacitance values depend on the choice of output trip points, even though C pf R pdf and C pr R pdr are constant for a given input trip point and waveform, because the pull-up and pull-down resistances depend on the choice of output trip points. We take a closer look at parasitic capacitance next.

Chapter start ] [ Previous page ] [ Next page ]

Teledyne Optech
CADalog.com - Countless CAD add-ons, plug-ins and more.

Internet Business Systems © 2016 Internet Business Systems, Inc.
595 Millich Dr., Suite 216, Campbell, CA 95008
+1 (408)-337-6870 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering EDACafe - Electronic Design Automation TechJobsCafe - Technical Jobs and Resumes  MCADCafe - Mechanical Design and Engineering ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy Policy