A 16-bit D/A interface with Sinc approximated semidigital reconstruction filter

Prev TOC Next

7.2. Bitstream D/A conversion system with time discrete filtering

Fig.7.1 illustrates the block diagram of a bitstream D/A conversion system[12]. This system consists of a digital filter, a noise shaper and a reconstruction

Fig.7.1: Bitstream D/A conversion system

filter. Eventually, the power amplifier can be integrated on the same chip. In the digital filter the data rate of the input digital word is increased by interpolative upsampling 64 times. The filter interpolates the input signal and calculates intermediate points. The low-pass filter limits sharply the audio-band at 20KHz. In order to reduce the quantization noise in the baseband two techniques are used: oversampling and noise shaping.

By oversampling in the digital filter, the quantization is performed at higher clock rates and the resulting quantization noise power is spread over a larger bandwidth. This yields lower noise in the baseband. Noise shaping is a technique used to reduce the quantization noise in the audioband, by shaping the quantization noise out of the baseband. In combination with oversampling this method gives sufficient reduction of the quantization noise to realize high accuracy systems. In the 1-bit D/A converter, the digital sequence present at the output of the noise-shaper (1,0,0,1,0…) it is translated into an accurate two-level analog signal (A,-A,-A,A,-A,…) with high linearity. In the same block, a sampled data FIR filter (LPD) will suppress the out-of-band noise. To reduce harmonic distortion and intermodulation products in the output power amplifier, the level of the high frequency quantization noise has to be lower than -50dB. A first order, continuous-time analog low pass filter (LPA) will reconstruct the signal by attenuating the spectral repetitions at multiples of sampling frequency.

In fig.7.1 the signal and the noise spectra of the D/A system are shown. For simplicity, the oversampling frequency is not drawn at the right scale (4 times instead of 64 times). Fig.a shows that a sampled signal consists of an infinite sequence of the original spectra shifted by multiples of fs. Therefore also the noise power is shown up to ½fs. Oversampling (see fig.b) spreads the noise over a larger frequency band and places the signal spectra further from each other. The noise shaper shapes the noise out of the baseband to higher frequencies (see fig.c). In fig.d+e, the signal at the output of the FIR filter (doted) and the signal at the output of the LPA filter (thick lines). The noise at high frequencies is filtered by the time discrete filter. The final operation, i.e. the low-pass continuous-time filtering, removes the undesired spectral repetitions from the signal.


Featured Video
Geospatial Analyst/Programmer for LANDIQ at Sacramento, California
Product Manager for CHA Consulting, Inc. at Boston, Massachusetts
GIS Data Analyst for CostQuest Associates, Inc. at Cincinnati, Ohio
Software Developer for CHA Consulting, Inc. at Norwell, Massachusetts
Mid-Level Mechanical Engineer for Kiewit at lenexa, Kansas
Mechanical Engineer for Allen & Shariff Corporation at Pittsburgh, Pennsylvania
Upcoming Events
GEO Business 2018 at 52 Upper Street London United Kingdom - May 22 - 23, 2018
Upper Midwest Geospatial Conference (UMGEOCON) at 521 East Ave North La Crosse WI - May 23 - 24, 2018
Locate 2018 at Pier 27, The Embarcadero San Francisco CA - May 30 - 31, 2018
2nd WY UAV Symposium at UW Convention Center 2229 Grand Ave LARAMIE WY - May 30 - 31, 2018
Teledyne Optech
Interdrone 2018

Internet Business Systems © 2018 Internet Business Systems, Inc.
25 North 14th Steet, Suite 710, San Jose, CA 95112
+1 (408) 882-6554 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering EDACafe - Electronic Design Automation TechJobsCafe - Technical Jobs and Resumes  MCADCafe - Mechanical Design and Engineering ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy PolicyAdvertise